Analog Bandwidth (-3 dB)

125 MHz

Rise Time (10% to 90%, typical)

≤2.8 ns

No. of Input/Output Channels

4 input analog channels
16 input digital channels (required to purchase the PLA2216 logic analyzer probe)

Sampling Mode

Real-time Sampling

Max. Sample Rate of Analog Channel

1.25 GSa/s (single-channel), 625 MSa/s (dual-channel), 312.5 MSa/s (full-channel)

Max. Memory Depth

50 Mpts (single-channel), 25 Mpts (dual-channel), 10 Mpts (full-channel)

Max. Waveform Capture Rate

30,000 wfms/s (Vector Mode) 1,000,000 wfms/s (UltraAcquire Mode)

Vertical Resolution

12 bits

Hardware Real-time Waveform Recording and Playing

Max. 500,000 frames

Peak Detection

Capture 1.6 ns glitches

LCD Size and Type

7'' capacitive multi-touch screen

Display Resolution

1024x600

Input Coupling

DC, AC, or GND

Input Impedance

1 MΩ ± 1%

Input Capacitance

15 pF ± 3 pF

Maximum Input Voltage

CAT I 300 Vrms, 400 Vpk (DC + Vpeak)

Number of Digital Channels

16 input channels (D0 to D15) (D0 to D7, D8 to D15)

Threshold Range

±15.0 V, in 10 mV step

Threshold Accuracy

±(100.00 mV + 3% of threshold setting)

Threshold Selection

TTL(1.4 V), CMOS5.0(2.5 V), CMOS3.3(1.65 V), CMOS2.5(1.25 V), CMOS1.8(0.9 V), ECL(-1.3 V), PECL(3.7 V), LVDS(1.2 V), 0.0V User (threshold adjustable for a single channel)

Max. Input Voltage

±40 V peak CAT I; transient overvoltage 800 Vpk

Max. Input Dynamic Range

±10 V + threshold

Minimum Voltage Swing

500 mVpp

Input Impedance about

101 kΩ

Probe Load about

8 pF

Vertical Resolution

1 bits

Range of Time Base

2 ns/div to 500 s/div

Trigger Source

Analog channel (CH1 to CH4), digital channel (D0 to D15)

Trigger Mode

Auto, Normal, Single

Trigger Coupling

DC coupling trigger
AC coupling trigger
High Frequency Rejection - Cut-off frequency to 120 kHz (internal trigger only)
Low Frequency Rejection - Cut-off frequency to 120 kHz (internal trigger only)

Trigger Type

Edge trigger, Pulse trigger, Slope trigger, Video trigger, Pattern trigger, Duration trigger, Timeout trigger, Runt trigger, Window trigger, Delay trigger, Setup/Hold trigger, Nth Edge trigger, RS232/UART, I2C, SPI, CAN

Search & Navigation Type

Edge, Pulse

Waveform  Measurement function

Yes

Waveform  Calculation function

Yes

Waveform Recording & Analysis

Yes

Serial  Decoding function

Yes

AutoScale

Min voltage > 10 mVpp, duty cycle > 1%, frequency > 35 Hz

Digital  Voltmeter Function

Yes; DC, AC+DCrms, ACrms

High-precision  Frequency  Counter

Yes

Command Set function

Yes

Processor

Cortex-A72 up to 1.8 GHz, 6-core processor

System  Memory

4 GB RAM

Operating System

Android

Internal Non-volatile Memory

8 GB

USB2.0 Host

1 on the front panel

USB2.0 Device

1 on the rear panel

LAN

1 on the rear panel, 10/100 Base-T, supporting LXI-C

Web Remote Control

Supports Web Control interface (input the IP address of the oscilloscope into the Web browser to display the operation interface of the oscilloscope)

AFG OUT - Waveform Output

No

AUX Output Interface

1 on the rear panel, BNC connector; Vo (H) ≥ 2.5 V open circuit, ≥1.0 V 50 Ω to GND; Vo (L) ≤ 0.7 V to load ≤4 mA, ≤0.25 V 50 Ω to GND

Trigger Output

Outputs a pulse signal when the oscilloscope is triggered

Pass/Fail Output

Output a pulse signal when a pass/fail event occurs. Supports user-defined pulse polarity and pulse time (100ns to 10 ms)

HDMI Video Output

1 on the rear panel, HDMI 1.4, A plug. It is used to connect to an external monitor or projector

Probe Compensation Output

1 kHz, 3 Vpp square waveform

Power Supply Interface

USB Type-C

Power Voltage

DC 12 V, 4 A

Power

Max. 48 W (when connected to various interfaces, USB storage device, active probes)

Recommended Calibration Interval

18 months

Operating Temperature Range

0℃ to 50℃

Dimensions

265.35 mm x 161.75 mm x 77.38 mm

Weight without package

1.78 kg